Norac UC5-BC-AP03 Bedienungsanleitung

Apache (2010+) Enhanced Stability Installation Manual AP03

74.4 Hydraulic Fitting Kit Details (P/N: 44865-03) Item Part Number Name QuantityPictureF04 103839 T ADAPTER - 6FJXR 6MJT 4F05 103312 MALE ADAPTE

85 Pre-Install Checklist The pre-install checklist is necessary to check the existing sprayer functionality before the installation. 1. Unfold

96 Ultrasonic Sensor Installation 6.1 Ultrasonic Sensor Serial Number Arrangement When installing the UC5 sensors, start with the smallest seria

106.2 Ultrasonic Sensor Mounting Guidelines The following guidelines will ensure optimal sensor performance and prevent sensor measurement . 1

116.3 Low Profile Bracket Mounting Guidelines 1. Minimize the distance between the bolts to prevent bending the bracket and prevent the bracket

126.4 Wing Sensor Installation 1. The sensor bracket should be oriented forward (ahead of the boom). 2. Typically the best mounting location fo

136.5 Rainflap Installation Rainflaps are only installed in the wing sensor brackets. 1. Insert one side of the rainflap rod into the pre-bent

146.6 Main Lift Sensor Installation 1. The main lift mounting bracket (B21) is the bracket with the longer mounting flange. 2. There are a var

157 Roll Sensor Installation 7.1 Bracket Assembly 1. Securely mount the roll sensors to the included roll sensor brackets using the #6 machine

167.2 Roll Sensor Mounting Guidelines: Trapeze-Suspended Booms 1. When mounting the roll sensors, mount one to the boom frame – lowest serial nu

Printed in Canada Copyright  2009 by NORAC Systems International Inc. Reorder P/N: UC5-BC-AP03-INST Rev I (Apache (2010+) Enhanced Stability) NOTICE

17 Figure 18: Reference Frame (Chassis) Roll Sensor Mounting

188 Module Installation An optional module mounting bracket kit is available for purchase from NORAC. The mounting brackets are compatible with

198.2 Valve Module 1. Install the valve module (E02) to the top of the NORAC valve block. Orient the 6-pin Deutsch (CANbus) connectors towards

20 Figure 22: Valve Module Bracket Installation 5. Connect the valve module CANbus to cable C01 from the control module. Route cable C02 from

218.3 Input Module 1. Install the input module (E03) on the boom near the sprayer valve block. Secure it to the boom using cable ties or option

229 Connecting the Sensors to the CANbus 1. Fasten the 8-way coupler to the boom with cable ties. Connect cable C02 from the input module to th

2310 Hydraulic Installation Ensure all pressure has been bled from the system before disconnecting any lines or fittings. Hydraulic pressure wi

2410.2 Valve Block Mounting 1. A suitable mounting location for the valve block is illustrated in Figure 27. 2. Insert the threaded rod into th

2510.3 Hydraulic Plumbing From this point on in the installation the booms will be inoperative until the hydraulics are fully installed. 1. Aft

2611 Software Setup 1. Start up the sprayer and test the sprayer’s functionality. The display terminal does not need to be powered on for the

Contents 1 Introduction ... 12

2712 Cable Drawings 12.1 ITEM C01: 43220-10 - CABLE UC5 NETWORK 14 AWG - 10M 12.2 ITEM C02: 43220-01 - CABLE UC5 NETWORK 14 AWG - 1M

2812.3 ITEM C04: 43220-05 - CABLE UC5 NETWORK 14 AWG - 5M 12.4 ITEM C05: 43210-20 - CABLE UC5 NETWORK 18 AWG - 20M

2912.5 ITEM C10: 43230-04 – CABLE UC5 VALVE DT TO DT

3012.6 ITEM C20: 43240-01 – CABLE UC5 INTERFACE TILT DT

3112.7 ITEM C21: 43240-22 – CABLE UC5 INTERFACE MAIN DT (240”)

3212.8 ITEM C30: 43250-04 – CABLE UC5 BATTERY AMP FUSED

Canada NORAC Systems International Inc. Phone: (+1) 306 664 6711 Toll Free: 1 800 667 3921 Shipping Address: 3702 Kinnear Place Saskatoon, SK S7P

11 Introduction Congratulations on your purchase of the NORAC UC5 Spray Height Control System. This system is manufactured with top quality comp

22 Technical Specifications CAN ICES-3(A)/NMB-3(A) This device complies with part 15 of the FCC Rules. Operation is subject t

33 General UC5 System Layout Figure 1 illustrates the general layout of the UC5 system components: Figure 1: General UC5 System Layout Do no

44 Kit Parts 4.1 Kit Overview Figure 2: AP03 System Parts

54.2 Hydraulic Plumbing Figure 3: AP03 Hydraulic Plumbing

64.3 List of Parts Item Part Number Name QuantityB05 44706-01 KIT CABLE TIE BLACK 10 PCS 21 IN 150 PCS 7.5 IN 1B17 44972 SENSOR MOUNTING BRACKET