Norac UC5-BC-HD07 Bedienungsanleitung

Hardi Aftermarket New Navigator (2007+) and New Commander (2005+) Installation Manual HD07

74.3 List of Parts Item Part Number Name QuantityB05 44706-01 KIT CABLE TIE BLACK 10 PCS 21 IN 150 PCS 7.5 IN 1B10 44728 MOUNTING BRACKET COMPLE

84.4 Hydraulic Fitting Kit Details (P/N: 44865-63) Item Part Number Name QuantityPictureF01 44928 ORIFICE INSERT .047 IN ONE WAY 4F02 103312 MALE

94.5 Optional Pressure and Tank Hose Kit (P/N: 44865-49) If a separate pressure and tank line from the tractor to the NORAC valve block is requir

105 Pre-Install Checklist The pre-install checklist is necessary to check the existing sprayer functionality before the installation. 1. Unfold

116 Ultrasonic Sensor Installation 6.1 Bracket Assembly Assemble the breakaway sensor bracket as illustrated in Figure 6, following the instruct

126.2 Ultrasonic Sensor Serial Number Arrangement When installing the UC5 sensors, start with the smallest serial number on the left-hand side, a

136.3 Ultrasonic Sensor Mounting Guidelines The following guidelines will ensure optimal sensor performance and prevent sensor measurement error.

146.4 Wing Sensor Installation 1. The sensor bracket should be oriented forward (ahead of the boom). 2. Typically the best mounting location fo

156.5 Main Lift Sensor Installation Figure 10: Main Lift Bracket Assembly 1. There are a variety of ways to mount the main lift bracket on mos

167 Roll Sensor Installation 7.1 Bracket Assembly 1. Securely mount the roll sensors to the included roll sensor brackets using the #6 machine

Printed in Canada Copyright  2009 by NORAC Systems International Inc. Reorder P/N: UC5-BC-HD07-INST Rev H (Hardi Aftermarket New Navigator (2007+) an

177.2 Roll Sensor Mounting Guidelines: Trapeze-Suspended Booms 1. When mounting the roll sensors, mount one to the trapeze link (boom frame) and

187.3 Roll Sensor Mounting on a Twin Force / Force FTZ Boom Figure 15: Boom Frame Roll Sensor Mounting (Viewed from the rear of sprayer) Figur

197.4 Roll Sensor Mounting on an Eagle Boom Figure 17: Roll Sensor Mounting (Viewed from the rear of sprayer)

208 Module Installation An optional module mounting bracket kit is available for purchase from NORAC. The mounting brackets are compatible with

218.2 Valve Module 1. Install the valve module (E02) to the top of the NORAC valve block. Orient the 6-pin Deutsch (CANbus) connectors towards

22 Figure 21: Valve Module Bracket Installation 5. Connect the valve module CANbus to cable C01 from the control module. Route cable C02 from

238.3 Input Module 1. Install the input module (E03) on the boom near the Hardi valve block. Secure it to the boom using cable ties or optional

249 Connecting the Sensors to the CANbus 1. Route cable C03 from the input module to the 8-way coupler (E11). 2. Connect both roll sensors to t

2510 Hydraulic Installation Ensure all pressure has been bled from the system before disconnecting any lines or fittings. Hydraulic pressure wi

2610.2 Valve Assembly: Double Acting 1. On a clean surface remove the plastic plugs from the block. 2. Install two 3/8” x 1/4” BSPP (HD01) fitt

Contents 1 Introduction ... 12

2710.3 Valve Block Mounting 1. A suitable mounting location for the valve block is illustrated in Figure 27. 2. Insert the threaded rod into th

2810.4 Hydraulic Plumbing: Single Acting From this point on in the installation the booms will be inoperative until the hydraulics are fully ins

2910.5 Hydraulic Plumbing: Double Acting 1. After the NORAC valve is mounted, the hydraulic hoses and fittings can be plumbed. The plumbing for

3011 Software Setup 1. Start up the sprayer and test the sprayer’s functionality. The display terminal does not need to be powered on for the

3112 Cable Drawings 12.1 ITEM C01: 43220-10 - CABLE UC5 NETWORK 14 AWG - 10M 12.2 ITEM C02: 43220-01 - CABLE UC5 NETWORK 14 AWG - 1M

3212.3 ITEM C03: 43220-03 - CABLE UC5 NETWORK 14 AWG - 3M 12.4 ITEM C05: 43210-20 - CABLE UC5 NETWORK 18 AWG - 20M

3312.5 ITEM C10: 43230-04 – CABLE UC5 VALVE DT TO DT

3412.6 ITEM C20: 43240-08 – CABLE UC5 INTERFACE TILT AMP (SUPERSEAL)

3512.7 ITEM C21: 43240-09 – CABLE UC5 INTERFACE MAIN AMP (SUPERSEAL 240” WITH BYPASS)

3612.8 ITEM C30: 43250-06 – CABLE UC5 BATTERY PIGTAIL FUSED

11 Introduction Congratulations on your purchase of the NORAC UC5 Spray Height Control System. This system is manufactured with top quality comp

Canada NORAC Systems International Inc. Phone: (+1) 306 664 6711 Toll Free: 1 800 667 3921 Shipping Address: 3702 Kinnear Place Saskatoon, SK S7P

22 Technical Specifications CAN ICES-3(A)/NMB-3(A) This device complies with part 15 of the FCC Rules. Operation is subject t

33 General UC5 System Layout Figure 1 illustrates the general layout of the UC5 system components: Figure 1: General UC5 System Layout

44 Kit Parts 4.1 Kit Overview Figure 2: HD03 System Parts

54.2 Hydraulic Plumbing Figure 3: HD03 Hydraulic Plumbing: Single Acting (Force Boom)

6 Figure 4: HD03 Hydraulic Plumbing: Double Acting (Eagle Boom)