Norac UC4+BC+MC2 Bedienungsanleitung

Miller Condor & New Holland Rear Mount Truss Boom Installation Manual Spray Height Control System Improving the competitiveness of Ind

74 INSTALLATION PROCEDURE 4.1 EXISTING SYSTEM CHECK It is necessary to check the existing system’s functionality before installing the UC4+ Spray

8 Table 4: Boom Test Record (WITHOUT UC4+ Spray Height Control system) Working RPM: Boom Trial #1 [Sec] Trial #2 [Sec] Trial #3 [Sec] Avg Time [Sec]

94.3 WING SENSOR INSTALLATION 1. Assemble the Breakaway Sensor Mounting Brackets (B11) as show in Figure 4 and Figure 5. Figure 4: Breakaway Sens

105. Sensor cables should run through the mounting bracket tube and then behind the member the bracket is mounted onto. Cable-tie the connector in

11 Apply a light coating of the supplied Permatex Anti-seize grease to all threaded parts upon installation. Figure 10: Sensor Serial Number Inst

124.4 MAIN LIFT SENSOR INSTALLATION 1. Assemble the main lift sensor bracket (B11) as shown in Figure 11. Figure 11: Main Lift Sensor Bracket 2.

134.5 ROLL SENSOR INSTALLATION Mount the roll sensors to the included roll sensor brackets using the machine screws and nylon lock nuts, as illustr

144.5.1 Boom Frame Roll Sensor Mounting 1. Use the supplied hardware to mount the boom frame roll sensor (E04) as shown in Figure 16 and Figure 19

154.5.2 Intermediate Frame Roll Sensor Mounting The intermediate frame roll sensor has the temperature probe on it. 1. It is often best to cable

16 Figure 19: Intermediate and Boom Frame Roll Sensor Mounting Boom Frame Roll Sensor Intermediate Frame Roll Sensor

Printed in Canada Copyright  2005-08 by NORAC Systems International Inc. Reorder P/N: UC4+BC+MC2-INST Rev C (Miller Condor & New Holland Rear Mo

174.5.3 Reference Frame Roll Sensor Mounting The reference frame roll sensor should be the highest serial number. 1. The reference frame (chassis

184.6 HYDRAULIC INSTALLATION WARNING! The hydraulic system creates very high pressure. Before disconnecting any hydraulic lines ensure all press

194.6.2 Valve Mounting 1. Mount the NORAC valve (V01) on the sprayer using the valve mounting bracket. 2. Screw short side of the threaded rods i

204.6.3 Hydraulic Plumbing WARNING! From this point in the installation the booms will be inoperative until the electronics are fully installed.

214.7 ELECTRICAL INSTALLATION 1. Install the UC4+ Control Panel (E01) in the cab of the sprayer. Mount the panel where it will be clearly visible

22Figure 25: Cable Configurations: C10, C11 and C14 2. Connect the UC4+ power cable (C10) to the UC4+ control panel in the sprayer cab. Ensure bot

237. Route C11 to the rear of the sprayer, in the vicinity of the valve block. 8. Connect the 6-pin shroud (S6) on C12 to the mating connector (T

24Figure 28: Cable Configurations: C11, C02, C02B and C05 IMPORTANT: Provide enough slack in all cables to account for the movement of the main s

254.8 COMPLETING THE INSTALLATION 1. Start up your sprayer and test the sprayer’s functionality. The NORAC Control Panel does not need to be powe

265 ELECTRICAL REFERENCE – CABLE DRAWINGS 5.1 ITEM C02: 44668 – CABLE SENSOR BRANCH

TABLE OF CONTENTS 1 INTRODUCTION ...

275.2 ITEM C02B: 44664 – CABLE UC4 CAN NODE DUAL

285.3 ITEM C03: 44656D – CABLE VALVE VARIABLE RATE DT

295.4 ITEM C05: 44674 – CABLE UC4 SENSOR ROLL BIAS

305.5 ITEM C10: 44650-39 – CABLE POWER GENERIC SELF-PROPELLED L = 100" (2.54m)

315.6 ITEM C11: 44651-03 – CABLE VALVE EXTENSION GENERIC 365” (9.27m)

325.7 ITEM C12: 44658-21 – CABLE UC4 INTERFACE GP ALL

335.8 ITEM C14: 44658-28 – CABLE UC4 INTERFACE POWER PIGTAIL

Canada NORAC Systems International Inc. CALL TOLL FREE: 1-800-667-3921 (306)664-6711 SHIPPING ADDRESS: 3702 Kinnear Place Sask

11 INTRODUCTION Congratulations on your purchase of the NORAC UC4+ Spray Height Control System. This system is manufactured with top quality comp

22 GENERAL SYSTEM DESCRIPTION Figure 1 depicts the general system layout of the UC4+ Spray Height Control System. Figure 1: System Components an

33 PARTS LISTS The parts that come with your UC4+ Spray Height Control System are listed in Table 1. The item number on the left side of this ta

4Table 2: 44865-59 - Hydraulics Fittings Kit Detail Item Part Number Name QuantityPictureF01 106314 MALE ADAPTER - 8MB 8MOR 2F02 104590 90 DEGREE AD

5The parts that come with your UC4+ System are shown below in their general installation configuration. Figure 2: UC4+ Spray Height Control System

6 Figure 3: Hydraulic Plumbing Schematic NOTE: Fitting F04 is not used for this install. The use of dielectric grease is not recommended on any