Norac UC4+BC+SC1 Bedienungsanleitung

SPRA-COUPE 7000 Series Installation Manual Spray Height Control System Improving the competitiveness of Industry and Agriculture through Prec

74 INSTALLATION PROCEDURE 4.1 EXISTING SYSTEM CHECK It is necessary to check the existing system’s functionality before installing the UC4+ Spray

8Table 4: Boom Test Record (WITHOUT UC4+ Spray Height Control system) Working RPM: Boom Trial #1 [Sec] Trial #2 [Sec] Trial #3 [Sec] Avg Time [Sec]

94.3 WING SENSOR INSTALLATION 1. Assemble the Breakaway Sensor Mounting Brackets (B11) as show in Figure 4 and Figure 5. Figure 4: Breakaway Sens

10proceeding to the largest serial number on the right hand side (Figure 10). 5. Sensor cables should run through the mounting bracket tube and t

11 Figure 9: Wing Sensor Mounting

12Apply a light coating of the supplied Permatex Anti-seize grease to all threaded parts upon installation. Figure 10: Sensor Serial Number Insta

134.4 MAIN LIFT SENSOR INSTALLATION 1. Assemble the main lift sensor bracket (B11) as shown in Figure 11. Figure 11: Main Lift Sensor Bracket 2.

144.5 ROLL SENSOR INSTALLATION Mount the roll sensors to the included roll sensor brackets using the machine screws and nylon lock nuts. (Figure 14

15 Figure 16: Roll Sensor Mounting with Respect to Sprayer Orientation 4.5.1 Boom Roll Sensor Mounting The boom roll sensor (E04) must be mounted t

16 Figure 17: Boom and Chassis Roll Sensors Correctly Mounted 4.5.3 Inverted Roll Sensor Mounting If desired, the Roll sensor may be mounted inver

Printed in Canada Copyright  2005-08 by NORAC Systems International Inc. Reorder P/N: UC4+BC+SC1-INST Rev H (SPRA-COUPE 7000 Series) NOTICE NORAC Sy

174.6 HYDRAULIC INSTALLATION WARNING! The hydraulic system creates very high pressure. Before disconnecting any hydraulic lines ensure all press

184.6.2 Valve Mounting 1. Mount the NORAC valve (V01) on the sprayer using the valve mounting bracket (B10). 2. As shown in Figure 22, screw shor

194.6.3 Hydraulic Plumbing WARNING! From this point in the installation the booms will be inoperative until the electronics are fully installed.

204.7 ELECTRICAL INSTALLATION 1. Install the UC4+ Control Panel (E01) in the cab of the sprayer. Mount the panel where it will be clearly visible

212. Remove the electrical panel from the right-hand side of the sprayer and locate the access hole on the top right hand side. 3. Connect the UC4

22 It may be easier installing the cables first, while installing the grommet (M15) later. 8. Route C01 through the grommet. Then route the val

23 Figure 29: Cable Configurations: C01, C02, C02B, C03 and C04 18. Connect the 6-pin Tower on the Valve Cable (C03) to the mating 6-pin Shroud on C

244.8 COMPLETING THE INSTALLATION 1. Start up your sprayer and test the sprayer’s functionality. The NORAC Control Panel does not need to be powe

255 ELECTRICAL REFERENCE – CABLE DRAWINGS 5.1 ITEM C01: 44662B – CABLE SENSOR TRUNK 5.2 ITEM C02: 44668 – CABLE SENSOR BRANCH

265.3 ITEM C02B: 44664 – CABLE UC4 CAN NODE DUAL

TABLE OF CONTENTS 1 INTRODUCTION ...

275.4 ITEM C03: 44656D – CABLE VALVE VARIABLE RATE DT

285.5 ITEM C04: 44651 – CABLE VALVE EXTENSION

295.6 ITEM C10: 44650-38 – CABLE UC4 POWER SPRA-COUPE 7000 SERIES <CABLE A>

305.7 ITEM C10: 44650-38 – CABLE UC4 POWER SPRA-COUPE 7000 SERIES <CABLE B>

315.8 ITEM C11: 44658-15 – CABLE UC4 JAM VALVE SPRA-COUPE 7000 SERIES

Canada NORAC Systems International Inc. CALL TOLL FREE: 1-800-667-3921 (306)664-6711 SHIPPING ADDRESS: 3702 Kinnear Place Saskatoon, SK S7P 0A6

11 INTRODUCTION Congratulations on your purchase of the NORAC UC4+ Spray Height Control System. This system is manufactured with top quality comp

22 GENERAL SYSTEM DESCRIPTION Figure 1 depicts the general system layout of the UC4+ Spray Height Control System. Figure 1: System Components an

33 PARTS LISTS The parts that come with your UC4+ System are listed in Table 1. The item number on the left side of this table references each p

4Table 2: 44865-29 - Hydraulics Fittings Kit Item Part Number Name QuantityPictureF02 103950 TEE ADAPTER - 6MBR 6MJT 2F03 103345 ELBOW ADAPTER - 6MJ

5The parts that come with your UC4+ Spray Height Control System are shown below in their general installation configuration. Figure 2: UC4+ Spray H

6 Figure 3: Hydraulic Components