Norac UC5-BC-WK01 Bedienungsanleitung

Walker Installation Manual WK01

74.4 Hydraulic Fitting Kit Details (P/N: 44865-73) Item Part Number Name Quantity PictureF01 104369 PLUG - 6MBP 2F02 103312 MALE ADAPTER - 6MB 6M

85 Pre-Install Checklist The pre-install checklist is necessary to check the existing sprayer functionality before the installation. 1. Unfold

96 Ultrasonic Sensor Installation 6.1 Ultrasonic Sensor Serial Number Arrangement When installing the UC5 sensors, start with the smallest seria

106.2 Ultrasonic Sensor Mounting Guidelines The following guidelines will ensure optimal sensor performance and prevent sensor measurement error.

116.3 Low Profile Bracket Mounting Guidelines 1. Minimize the distance between the bolts to prevent bending the bracket and prevent the bracket

126.4 Wing Sensor Installation 1. The wing sensor mounting brackets (B20) are the two brackets with the shorter mounting flange. 2. The sensor

136.5 Rainflap Installation Rainflaps are only installed in the wing sensor brackets. 1. Insert one side of the rainflap rod into the pre-bent

146.6 Main Lift Sensor Installation 1. The main lift mounting bracket (B21) is the bracket with the longer mounting flange. 2. There are a var

157 Roll Sensor Installation 7.1 Bracket Assembly 1. Securely mount the roll sensors to the included roll sensor brackets using the #6 machine

167.2 Roll Sensor Mounting Guidelines: Front Mounted Rigid Booms 1. When mounting the roll sensors, mount the lowest serial number onto the boom

Printed in Canada Copyright  2014 by NORAC Systems International Inc. Reorder P/N: UC5-BC-WK01-INST Rev A (Walker) NOTICE: NORAC Systems Internati

177.3 Roll Sensor Mounting Figure 18: Roll Sensor Mounting Boom Frame Roll Sensor Chassis Roll Sensor

188 Module Installation An optional module mounting bracket kit is available for purchase from NORAC. The mounting brackets are compatible with

19 Figure 20: Power Connection Figure 21: Cabling Access through Floor Hatch

208.2 Input Module 1. Install the input module (E03) near the Walker valve block and secure it using cable ties. 2. Connect the free end of t

218. Connect a second cable C02 to the 3-way coupler (E10) and route towards the valve module. Figure 23: Input Module Connections Figure 24:

228.3 Valve Module 1. Install the valve module (E02) to the top of the NORAC valve block. Orient the 6-pin Deutsch (CANbus) connectors towards

23 Figure 27: Valve Module Bracket Installation 5. Connect cable C02 to the valve module CANbus from the 3-way coupler (E10). Route cable C03

249 Connecting the Sensors to the CANbus 1. Connect the chassis roll sensor to the 3-way coupler (E10). 2. Fasten the 8-way coupler (E11) to

2510 Hydraulic Installation Ensure all pressure has been bled from the system before disconnecting any lines or fittings. Hydraulic pressure wi

2610.2 Valve Block Mounting 1. Mount the valve block using the mounting bracket (B01) as shown in Figure 30 and Figure 31. Figure 30: Valve

Contents 1 Introduction ... 12

2710.3 Hydraulic Plumbing From this point on in the installation the booms will be inoperative until the hydraulics are fully installed. 1. Aft

2811. At the accumulator, remove the existing fitting from between the hoses and accumulator (Figure 33). Insert the 6FJXL 6MJT tee (F09) in its

2911 Software Setup 1. Start up the sprayer and test the sprayer’s functionality. The display terminal does not need to be powered on for the o

3012 Cable Drawings 12.1 ITEM C01: 43220-07 - CABLE UC5 NETWORK 14 AWG – 7M 12.2 ITEM C02: 43220-03 - CABLE UC5 NETWORK 14 AWG - 3M

3112.3 ITEM C03: 43220-0.5 - CABLE UC5 NETWORK 14 AWG – 0.5M 12.4 ITEM C05: 43210-20 - CABLE UC5 NETWORK 18 AWG - 20M

3212.5 ITEM C10: 43230-04 – CABLE UC5 VALVE DT TO DT

3312.6 ITEM C20: 43240-01 – CABLE UC5 INTERFACE TILT DT

3412.7 ITEM C21: 43240-07 – CABLE UC5 INTERFACE MAIN DT (WITH AUX 1 & 2)

3512.8 ITEM C30: 43250-04 – CABLE UC5 BATTERY AMP FUSED

Canada NORAC Systems International Inc. Phone: (+1) 306 664 6711 Toll Free: 1 800 667 3921 Shipping Address: 3702 Kinnear Place Saskatoon, SK S7P

11 Introduction Congratulations on your purchase of the NORAC UC5 Spray Height Control System. This system is manufactured with top quality comp

22 Technical Specifications CAN ICES-3(A)/NMB-3(A) This device complies with part 15 of the FCC Rules. Operation is subject t

33 General UC5 System Layout Figure 1 illustrates the general layout of the UC5 system components: Figure 1: General UC5 System Layout Do n

44 Kit Parts 4.1 Kit Overview Figure 2: WK01 System Parts

54.2 Hydraulic Plumbing Figure 3: WK01 Hydraulic Plumbing

64.3 List of Parts Item Part Number Name QuantityB01 44700-07 MOUNTING BRACKET VALVE NITRO 4000 SERIES BC KIT 1B05 44706-01 KIT CABLE TIE BLACK 1