Norac 5467BC-4B Bedienungsanleitung

UC5 Active Roll ControlTM (44962D) Installation Manual 5467BC-4B

74 Position Sensor Installation 1. Remove the rubber bumpers on both ends of the roll frame (Figure 3). Figure 3: Rubber Bumper Location 2.

84. Mount the brackets (B09) as shown in Figure 5. Install two (2) cable ties per bracket. Figure 5: Bracket Mounting (Looking from the Rear) 5

9 Figure 7: Center Mark Location Centerline Mark 4” (100mm)

105 Hydraulic Installation Ensure all pressure has been bled from the system before disconnecting any lines or fittings. Hydraulic pressure wil

115.2 Expansion Block Assembly 1. Loosen the existing 2-station valve block so that it can be moved and/or twisted for the installation of the e

125.3 Roll Cylinder Installation 1. Remove the link arm (black square tube) connected between the parallel lift frame and roll frame. See Figur

135. Loosen the plastic port plugs and extend the cylinder to line up the hole in the intermediate frame and the cylinder. 6. Install B10 from t

1410. In some cases, the bracket has failed at the weld shown in Figure 15. It is recommended that all sprayers with roll control add weld to the

155.4 Hydraulic Plumbing From this point on in the installation the booms will be inoperative until the hydraulics are fully installed. 1. Afte

166. Route the secondary tank line (H78) to the inlet on the sprayer’s hydraulic in-line filter and use a 6FORXR-6MORT tee fitting (F10) to tee i

Printed in Canada Copyright  2010 by NORAC Systems International Inc. Reorder P/N: 5467BC-4B-INST Rev H (UC5 Active Roll Control (44962D)) NOTICE:

17 Figure 18: Secondary Tank Line (H78) (teed into the tank return near the in-line filter) The load-sense return line (also teed into the in-lin

187. Install hoses H72 to the roll cylinder that was previously installed. Route the hoses to the NORAC valve block. 8. Connect the hose atta

196 Electrical Installation 1. Locate the valve module installed on the NORAC valve block. Remove the plugs installed in positions 7 and 8.

20 Figure 22: Electrical Installation Only the components shown in black are included in this kit.

217 Software Setup 1. Start up the sprayer and test the sprayer’s functionality. The display terminal does not need to be powered on for the o

228 System Maintenance For good performance in corners, when driving over terraces or through ditches at an angle, or in hard steer situations i

239 Cable Drawings 9.1 ITEM C04: 43220-01 - CABLE UC5 NETWORK 14 AWG – 1M 9.2 ITEM C10: 43230-04 – CABLE UC5 VALVE DT TO DT

Canada NORAC Systems International Inc. Phone: (+1) 306 664 6711 Toll Free: 1 800 667 3921 Shipping Address: 3702 Kinnear Place Saskatoon, SK S7P

Contents 1 Introduction ... 12

11 Introduction Congratulations on your purchase of the NORAC UC5 Spray Height Control System. This system is manufactured with top quality comp

22 Technical Specifications CAN ICES-3(A)/NMB-3(A) This device complies with part 15 of the FCC Rules. Operation is subject t

33 Kit Parts 3.1 Kit Overview Figure 1: UC5 Roll Control Parts

43.2 Hydraulic Plumbing Figure 2: UC5 Roll Control Hydraulic Plumbing

53.3 List of Parts This kit is to be used when installing the Active Roll Control option with existing John Deere installations that have a valve

63.4 Active Roll Hydraulic Fittings Kit Details (P/N: 44865-38) Item Part Number Name QuantityPictureF10 104586 TEE ADAPTER - 6FORXR 6MORT 3F11