Norac UC4+BC+GM1 Bedienungsanleitung

Gregson Maverick 120 Series Installation Manual Spray Height Control System Improving the competitiveness of Industry and Agriculture through

84 INSTALLATION PROCEDURE 4.1 EXISTING SYSTEM CHECK It is necessary to check the existing system’s functionality before installing the UC4+ Spray

9Table 4: Boom Test Record (WITHOUT UC4+ Spray Height Control system) Working RPM: Boom Trial #1 [Sec] Trial #2 [Sec] Trial #3 [Sec] Avg Time [Sec]

104.3 WING SENSOR INSTALLATION 1. Assemble the Breakaway Sensor Mounting Brackets (B11) as show in Figure 4 and Figure 5. Figure 4: Breakaway Sen

11(ahead) of the boom (see Figure 6 and Figure 8). When installing the UC4+ sensors (E02), start with the smallest serial number on the left hand

12Apply a light coating of the supplied Permatex Anti-seize grease to all threaded parts upon installation. Figure 9: Sensor Serial Number Instal

134.4 MAIN LIFT SENSOR INSTALLATION 1. Assemble the main lift sensor bracket (B11) as shown in Figure 10. Figure 10: Main Lift Sensor Bracket 2.

144.5 ROLL SENSOR INSTALLATION Before installing the roll sensors you must determine if your sprayer has a trapeze style or center pivot style boom

154.6 ROLL SENSOR INSTALLATION (TRAPEZE STYLE BOOMS)Mount the roll sensors to the included roll sensor brackets using the machine screws and nylon

164.6.1 Boom Frame Roll Sensor Mounting 1. Use the supplied hardware to mount the boom frame roll sensor (E04) as shown in Figure 17. When mount

174.6.2 Chassis Roll Sensor Mounting 1. It is often best to cable tie the chassis roll sensor in place. When mounting the chassis roll sensor fol

Printed in Canada Copyright  2005-08 by NORAC Systems International Inc. Reorder P/N: UC4+BC+GM1-INST Rev F (Gregson Maverick 120 Series) NOTICE NOR

184.7 ROLL SENSOR INSTALLATION (CENTER PIVOT STYLE BOOMS)Mount the roll sensors to the included roll sensor brackets using the machine screws and n

19 Figure 21: Roll Sensor Mounting with Respect to Sprayer Orientation 4.7.1 Boom Roll Sensor Mounting The boom roll sensor (E04) must be mounted t

20 Figure 22: Boom and Chassis Roll Sensors Correctly Mounted 4.8 INVERTED ROLL SENSOR MOUNTING If desired, the Roll sensor may be mounted inverte

214.10 HYDRAULIC INSTALLATION WARNING! The hydraulic system creates very high pressure. Before disconnecting any hydraulic lines ensure all pres

224.10.2 Valve Mounting 1. Mount the NORAC valve (V01) on the sprayer using the valve mounting bracket (B10). 2. As shown in Figure 27, screw shor

234.10.3 Hydraulic Plumbing WARNING! From this point in the installation the booms will be inoperative until the electronics are fully installed.

244.11 ELECTRICAL INSTALLATION 1. Install the UC4+ Control Panel (E01) in the cab of the sprayer. Mount the panel where it will be clearly visibl

252. On the right-hand side of the cab there is an electrical access panel. The tee connection on the UC4+ power cable (C10) must be connected bet

2610. The connectors on the valve cable (C03) are marked RIGHT UP, LEFT UP, RIGHT DOWN and LEFT DOWN. Cables labeled with UP go on the same side a

274.12 COMPLETING THE INSTALLATION 1. Start up your sprayer and test the sprayer’s functionality. The NORAC Control Panel does not need to be pow

TABLE OF CONTENTS 1 INTRODUCTION ...

285 ELECTRICAL REFERENCE – CABLE DRAWINGS 5.1 ITEM C01: 44662B-40 – SENSOR TRUNK CABLE 5.2 ITEM C02: 44668 – SENSOR BRANCH CABLE

295.3 ITEM C02B: 44664 – CABLE UC4 CAN NODE DUAL

305.4 ITEM C03: 44656D – CABLE VALVE VARIABLE RATE DT

315.5 ITEM C04: 44651 – VALVE EXTENSION CABLE

325.6 ITEM C10: 44650-11 – POWER CABLE GREGSON MAVERICK

33 www.norac.ca Canada NORAC Systems International Inc. CALL TOLL FREE: 1-800-667-3921 (306)664-6711 SHIPPING ADDRESS: 3702 Kinnear Place Saskatoon

21 INTRODUCTION Congratulations on your purchase of the NORAC UC4+ Spray Height Control System. This system is manufactured with top quality comp

32 GENERAL SYSTEM DESCRIPTION Figure 1 depicts the general system layout of the UC4+ Spray Height Control system. Figure 1: System Components an

43 PARTS LISTS The parts that come with your UC4+ Sprayer Boom System are listed in Table 1. The item number on the left side of this table refe

5Table 2: 44865-10: Hydraulics Fittings Kit Details Item Part Number Name QuantityPictureF01 44928 ORIFICE INSERT .047 IN ONE WAY 4F02 103312 MALE A

6The parts that come with your UC4+ Spray Height Control system are shown below in their general installation configuration. Figure 2: UC4+ Spray H

7 Figure 3: Hydraulic Components